nv-l
[Top] [All Lists]

[NV-L] NV 7.1.4 AIX--advice on ksh nmdemandpoll script--coprocessing

To: "Tivoli NetView Discussions" <nv-l@lists.ca.ibm.com>
Subject: [NV-L] NV 7.1.4 AIX--advice on ksh nmdemandpoll script--coprocessing
From: "Van Order, Drew \(US - Hermitage\)" <dvanorder@deloitte.com>
Date: Thu, 19 Oct 2006 07:13:11 -0500
Delivery-date: Thu, 19 Oct 2006 13:35:12 +0100
Envelope-to: nv-l-archive@lists.skills-1st.co.uk
Importance: normal
List-help: <mailto:nv-l-request@lists.ca.ibm.com?subject=help>
List-id: Tivoli NetView Discussions <nv-l.lists.ca.ibm.com>
List-post: <mailto:nv-l@lists.ca.ibm.com>
List-subscribe: <http://lists.ca.ibm.com/mailman/listinfo/nv-l>, <mailto:nv-l-request@lists.ca.ibm.com?subject=subscribe>
List-unsubscribe: <http://lists.ca.ibm.com/mailman/listinfo/nv-l>, <mailto:nv-l-request@lists.ca.ibm.com?subject=unsubscribe>
Priority: normal
Reply-to: Tivoli NetView Discussions <nv-l@lists.ca.ibm.com>
Sender: nv-l-bounces@lists.ca.ibm.com
Thread-index: Acbzd/ID9UpCwKxmRl65lHliU5MS3w==
Thread-topic: NV 7.1.4 AIX--advice on ksh nmdemandpoll script--coprocessing

Hi all,

Our DNOC needs a report that shows what IP addresses are managed via SNMP query versus ping. I searched the archives and it appears one can't get this report using nvdbformat--isSNMPSupported is not an accurate indicator. So, I'm getting the list of IP's that match isSNMPSupported=TRUE from nvdbformat, then feeding the list into `ndmdemandpoll $hostname |grep "Get SNMP status"`. This will do the job, but we all know nmdemandpoll kills CPU if it takes any time at all to run. I have 1500 addresses to cycle through.

So, I figure I can kill nmdemandpoll if it's going to take longer than 15 seconds to finish, log the IP address that needed to be killed, then go back to the loop. No problem, except I'm a novice ksh scripter, and having trouble with co-processes (required to watch the nmdemandpoll PID because nothing will occur until nmdemandpoll finishes, right?). If someone can help me with the logic, I'll post the whole smash for everyone to use when it's finished.

This works fine, just takes forever, and sends uptime values skyward. It sets off NetIQ alerts for CPU utilization.

# Read in IP address list from NVout.report
# nv_getSNMPquerystatus.sh < NVout.report

while read ipAddress
do
       nmdemandpoll $ipAddress | grep "Get SNMP status"
       if [[ $? -eq 0 ]]
       then
       echo "$ipAddress is currently monitored using SNMP query"
       else
       echo "$ipAddress is currently NOT monitored using SNMP query"
       fi
done

Many thanks in advance to anyone with advice on how to finish this one off. --Drew



Drew Van Order
Information Technology Services
Deloitte Services LP
Tel: +1 615 882 7836
www.deloitte.com



This message (including any attachments) contains confidential information intended for a specific individual and purpose, and is protected by law.  If you are not the intended recipient, you should delete this message. 

Any disclosure, copying, or distribution of this message, or the taking of any action based on it, is strictly prohibited. [v.E.1]
_______________________________________________
NV-L mailing list
NV-L@lists.ca.ibm.com
Unsubscribe:NV-L-leave@lists.ca.ibm.com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to 
internal IBM'ers only)
<Prev in Thread] Current Thread [Next in Thread>

Archive operated by Skills 1st Ltd

See also: The NetView Web