At 10:58 AM 06-12-00 +1100, you wrote:
>>Hi,
>>
>>I have problems loading HP MIB tables on Netview.
>What are the problems you run into? What are the errror messages?
The error message is :
"Error detected while loading MIB File: /usr/OV/snmp_mibs/hpicfoid.mib.
This MIB cannot be loaded until the following problem is corrected:
Line 10: Error defining object: found 'MODULE-IDENTITY'
Expected one of the following:
OBJECT-IDENTIFIER
OBJECT-TYPE
TRAP-TYPE
::=
"
So I gather its a parsing error and perhaps the keyword isn't defined
anywhere, but I can't locate which MIB I should lod before that.
>> It seems to work fine
>>until I get to specific devices. Has anyone had any experience loading HP
>>MIBs? I'm not particularly sure if they are SNMPv1 or SNMPv2 or not.
>You can open the MIB file with a text editor and look at the header which
>will tell you whether it is v1 or v2.
Here are the first few lines of it:
" HP-ICF-OID DEFINITIONS ::= BEGIN
IMPORTS
enterprises, MODULE-IDENTITY, OBJECT-IDENTITY
FROM SNMPv2-SMI;
hp OBJECT IDENTIFIER ::= { enterprises 11 }
nm OBJECT IDENTIFIER ::= { hp 2 }
icf MODULE-IDENTITY
LAST-UPDATED "9809240004Z"
ORGANIZATION "Hewlett Packard Company,
Workgroup Networks Division"
CONTACT-INFO "Hewlett Packard Company
8000 Foothills Blvd.
Roseville, CA 95747"
DESCRIPTION "This MIB module describes devices in the HP
Integrated Communication Facility product
line."
"
I guess it would be a SNMPv2 file, however when I try to load it with the
SNMPv1/SNMPv2 command, the SNMPv1/SNMPv2 browser does not seem to load
properly. When I do browse the messages come up saying "Sending SNMPv1
request to x.y.z.a" and some time later it will come back with "SNMP Error:
SNMPAPI_TL_TIMEOUT - No Response before timeout" And the timeout is set up
60 seconds which is way above what I can telnet and ping to the device.
>> Would
>>that be my problem? Because I'm loading the MIBs via SNMP option and not
>>the SNMPv1/SNMPv2 option.
Thanks for you attention - much appreciated.
Regards,
Ronald Ng
Associate Network Specialist - Network Infrastructure Services
Office : (02) 9937 8351 Mobile : 0401 149 331 Fax: (02) 9937 8100
IBM Global Services Australia
Level 1, 55 Christie Street
St. Leonards NSW 2065
E-Mail : ronaldng@au1.ibm.com
Joe Fernandez <jfernand@kardinia.com> on 07/12/2000 10:05:39 AM
Please respond to IBM NetView Discussion <nv-l@tkg.com>
To: IBM NetView Discussion <nv-l@tkg.com>
cc: (bcc: Ronald Ng/Australia/IBM)
Subject: Re: [NV-L] Loading HP MIBs
At 10:58 AM 06-12-00 +1100, you wrote:
>Hi,
>
>I have problems loading HP MIB tables on Netview.
What are the problems you run into? What are the errror messages?
> It seems to work fine
>until I get to specific devices. Has anyone had any experience loading HP
>MIBs? I'm not particularly sure if they are SNMPv1 or SNMPv2 or not.
You can open the MIB file with a text editor and look at the header which
will tell you whether it is v1 or v2.
> Would
>that be my problem? Because I'm loading the MIBs via SNMP option and not
>the SNMPv1/SNMPv2 option.
>
>Regards,
> Ronald Ng
> Associate Network Specialist - Network Infrastructure Services
> Office : (02) 9937 8351 Mobile : 0401 149 331 Fax: (02) 9937 8100
>
>IBM Global Services Australia
> Level 1, 55 Christie Street
> St. Leonards NSW 2065
>E-Mail : ronaldng@au1.ibm.com
>
>_________________________________________________________________________
>NV-L List information and Archives: http://www.tkg.com/nv-l
>
Joe Fernandez
Kardinia Software
jfernand@kardinia.com
http://www.kardinia.com
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
|