I had the same problem as you and fixed it with found on IBM.com
<< ERROR: Customize script for fileset OVWIN exited with code 2.
ERR_cfgbf_001 nvconfigbf: Failing doing configuration with exit code 2
base: Failure running script or command '/usr/OV/install/tools/nvconfigbf'
ERR_bcfg_210 base: Failing base.config with exit code 2 Cause ovstart has
timed out waiting for ovspmd to initialize. ovspmd is busy closing file
descriptors based on the ulimit specification for "nofiles". The usual case
is that the "unlimited" specification has been chosen, or some other
extremely high value. Solution If the ulimit specification for nofiles is
set to or defaulting to "unlimited", -1 (minus 1), or greater than 32767,
change it to 32767. >>
>>
change the value to 32767 and it should work fine.
Tilo Strauch
------------------------------------------------------------------------
Netzwerkmanagement
------------------------------------------------------------------------
Deutsche Rentenversicherung
Rechenzentrum Leipzig e.V.
Tel.: +49 0341 9170-220
Fax: +49 0341 9110-806
------------------------------------------------------------------------
mailto:tilo.strauch@rzleipzig.de
Franck Mercier
<franck.mercier@f
r.ibm.com> An
Gesendet von: nv-l@lists.us.ibm.com
owner-nv-l@lists. Kopie
us.ibm.com Jennifer Parker
<jennpa@us.ibm.com>, Jeffrey
Keller <kellerje@us.ibm.com>,
19.05.2004 11:23 Olivier Lesourd
<olesourd@fr.ibm.com>
Thema
Bitte antworten Re: [nv-l] NV 714 installation
an error [virengeprüft]
nv-l@lists.us.ibm
.com
Hello,
I have tried to install on AIX 5.2 ML02 with the system default value
of nofiles to 2000
and i still get the same problem ....
So the question is : which value must we have to set to have a succesful
NV714 insatllation ?
Up to now i only succeed by downgrading to AIX433 ML09 .
Thanks and regards
Franck MERCIER
Sce 1073 .
West Support Specialist for TIVOLI Products
IBM Global Services / Integrated Technology Services
Mailto : franck.mercier@fr.ibm.com
George deSocio
<desocio@us.ibm.c
om> To
Sent by: nv-l@lists.us.ibm.com
owner-nv-l@lists. cc
us.ibm.com
Subject
Re: [nv-l] NV 714 installation
23/04/2004 23:59 error
Please respond to
nv-l
Mario,
Your AIX system has ulimit for nofiles (ulimit -n) set too high. Change it
to 32767.
Since you are in a Framework environment, you must reboot after changing
ulimit for nofiles (ulimit -n).
How to do this: <backup files before you change them>
You need to change the default ulimit for nofiles (ulimit -n) for root.
This is in file /etc/security/limits <see the comments within the file>
After saving that file, telnet or other login to the machine as root to
check. After logging in, issue
the "ulimit -a" command. nofiles should be 32767 (as changed in
/etc/security/limits).
If still unlimited, check profile and shell rc files, etc.
After you have caused root default ulimit for nofiles to be 32767 and
proven it is true by the login test,
reboot.
Then as the other information instructs, clean up the installation using
the uninstall script on the cdrom.
Install. again.
Regards,
Geo.
George deSocio
IBM Americas Support - Distributed Network Management
Dept 46-E1ZA
IBM B660 CC102
HWY 54 & 600 Park Offices
Research Triangle Park, NC 27709
919-254-2259 (T/L 444) Fax: 919-543-7936 (T/L 441)
E-Mail: desocio@us.ibm.com
Expand your IBM Tivoli product knowledge by participating in Support
Technical Exchange:
http://www-3.ibm.com/software/sysmgmt/products/support/supp_tech_exch.html
Mario Behring <mariobehring@yahoo.com>
Sent by: owner-nv-l@lists.us.ibm.com
To
nv-l@lists.us.ibm.co
04/23/2004 03:41 PM m
cc
Please respond to Subject
nv-l [nv-l] NV 714
installation error
Hi list,
During a NetView 7.1.4 for AIX fresh install through Framework 4.1.1 at an
AIX 5.2 box I got the following error message:
Something went wrong:
Media Packet: "/mnt/cdrom/FILE33.PKT"
tvnmcnvq:FAILED (soft error)
Failure: the last few lines of the error log
(/tmp/NVS_714_NVFCONF_after.error):
+ echo Please check the log file /tmp/update.log for more details about
the errors.
+ 1>& 2
Please check the log file /tmp/update.log for more details about the
errors.
+ echo Then run the uninstnv script on the NetView cdrom to uninstall
NetView,
+ 1>& 2
Then run the uninstnv script on the NetView cdrom to uninstall NetView,
+ echo fix the errors and reinstall again.
+ 1>& 2
fix the errors and reinstall again.
+ exit 1
Completed (with errors).
All pre-requisites are installed, including the Tivoli NetView Framework
Patch 7.1, both on the TMR and on the ManagedNode that will be the NV
Server. The /tmp/update.log file (mentioned above) has the following
output:
D/N: GC23-4482-06
P/N: CT11VML
Fri Apr 23 13:31:07 EDT 2004
Initializing the Tracing and Logging...
Done.
======= Fri Apr 23 13:31:10 EDT 2004 BEGINNING NVCONFIGURE
* Running customize script for fileset OVMIN-LICENSE.
* Making links....
* Running customize script for fileset OVMIN.
* Making links....
* Running customize script for fileset OVWIN.
NOTE: Linking security support for nvsecd daemon.
NOTE: Configuring ovwdb
NOTE: Configuring nvsecd
NOTE: Starting nvsecd
ovstart: unable to contact ovspmd: No such file or directory
awk: 0602-533 Cannot find or open file 21494.
The input line number is 0. The file is 21494.
The source line number is 1.
ERROR: Unable to start nvsecd with ovstart.
ERROR: Unable to start nvsecd with ovstart.
ERR_0003_040
ERR_0003_040
+ dspmsg -s 5 nv6000.cat 9999 customize: Failing customize with exit
code %s\n 2
+ 1>> /tmp/update.log
customize: Failing customize with exit code 2
ERROR: Customize script for fileset OVWIN exited with code 2.
ERR_cfgbf_001
nvconfigbf: Failing doing configuration with exit code 2
base: Failure running script or command
'/usr/OV/install/tools/nvconfigbf'
ERR_bcfg_210
base: Failing base.config with exit code 2
Any ideas ?
Thank you.
Mario Behring
Tivoli Certified Consultant
IBM Brazil
mariob@br.ibm.com
mariobehring@yahoo.com
__________________________________
Do you Yahoo!?
Yahoo! Photos: High-quality 4x6 digital prints for 25¢
http://photos.yahoo.com/ph/print_splash
|