nv-l
[Top] [All Lists]

Re: [NV-L] Monitor IDSN Backup & Natted Devices

To: Tivoli NetView Discussions <nv-l@lists.ca.ibm.com>
Subject: Re: [NV-L] Monitor IDSN Backup & Natted Devices
From: Leslie Clark <lclark@us.ibm.com>
Date: Mon, 26 Feb 2007 09:56:30 -0500
Delivery-date: Mon, 26 Feb 2007 14:58:51 +0000
Envelope-to: nv-l-archive@lists.skills-1st.co.uk
In-reply-to: <OF3E133931.7F5D14F0-ON6525728E.0015BEAD-6525728E.0016097C@in.ibm.com>
List-help: <mailto:nv-l-request@lists.ca.ibm.com?subject=help>
List-id: Tivoli NetView Discussions <nv-l.lists.ca.ibm.com>
List-post: <mailto:nv-l@lists.ca.ibm.com>
List-subscribe: <http://lists.ca.ibm.com/mailman/listinfo/nv-l>, <mailto:nv-l-request@lists.ca.ibm.com?subject=subscribe>
List-unsubscribe: <http://lists.ca.ibm.com/mailman/listinfo/nv-l>, <mailto:nv-l-request@lists.ca.ibm.com?subject=unsubscribe>
Reply-to: Tivoli NetView Discussions <nv-l@lists.ca.ibm.com>
Sender: nv-l-bounces@lists.ca.ibm.com

For the unnumbered BRIs, you cannot use the + method. It is possible that Netview will discover those and draw them with address 0.0.0.0 but only if it mistakes them for unnumbered serials and if the other end of the connection is in the map. Most likely you will have to monitor them with snmpcollect. Set a threshold on ifOperStatus for that particular ifIndex number. Note that snmpCollect thresholding only works in a positive direction, and for dialers you would want a threshold event when it comes up (1) and a rearm when it goes down (2 or 5). To do that, you would define an _expression_ in /usr/OV/conf/mibExpr.conf for ifOperStatus * -1. Then you can set your threshold for when it is > -2 and rearm at -2.

For NAT, well, Netview does not support NAT. You can do some basic polling of IP up/down on the NATted addresses, but it is best if you do NOT have SNMP access to those addresses. If Netview gets responses to SNMP queries containing addresses that conflict with the NATted address, it will  likely discard the device.

Cordially,

Leslie A. Clark
IT Services Specialist, Network Mgmt
Information Technology Services Americas
IBM Global Services
(248) 552-4968 Voicemail, Fax, Pager



Santosh R Karekar <skarekar@in.ibm.com>
Sent by: nv-l-bounces@lists.ca.ibm.com

02/25/2007 11:00 PM
Please respond to
Tivoli NetView Discussions <nv-l@lists.ca.ibm.com>

To
nv-l@lists.ca.ibm.com
cc
Subject
[NV-L] Monitor IDSN Backup & Natted Devices





Hi,

To monitor backup ISDN whether we should add the  prefix  "+" with the
nodes devices LAN ip address (or) where we should add the ISDN IP address
range with a prefix "+". What would be the address if we are using dialers
and there is no ip address assigned to the ISDN BRI interface.

What is required to monitor the Natted Devices.

Thanx in advance.

_______________________________________________
NV-L mailing list
NV-L@lists.ca.ibm.com
Unsubscribe:NV-L-leave@lists.ca.ibm.com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to internal IBM'ers only)

_______________________________________________
NV-L mailing list
NV-L@lists.ca.ibm.com
Unsubscribe:NV-L-leave@lists.ca.ibm.com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to 
internal IBM'ers only)
<Prev in Thread] Current Thread [Next in Thread>

Archive operated by Skills 1st Ltd

See also: The NetView Web