Re: User2 Status

["Bingen, Jim D" <Jim.Bingen@NAVISTAR.COM>]

When I use the mib browser on these units, I get a status of "up". I would
assume it must be interpreting a 1 as up.

I'll put a call in to support and see what they have to say.

Thanks.

                -----Original Message-----
                From:   Desai, Aditya [mailto:DesaiA@USA.REDCROSS.ORG]
                Sent:   Thursday, October 07, 1999 9:58 AM
                To:     NV-L@UCSBVM.ucsb.edu
                Subject:        Re: User2 Status

                Hi Leslie

                I have seen similar behaviour on two of our cisco 4500
routers where an link
                previously in admin down state, after bringing it up, would
stay as user 1
                state on Netview.  We are running 5.1.2 on AIX.

                Thanks

                Ed Desai

                American Red Cross

                -----Original Message-----
                From: Leslie Clark [mailto:NV-L@UCSBVM.ucsb.edu]
                Sent: Thursday, October 07, 1999 9:54 AM
                To: NV-L@UCSBVM.ucsb.edu; lclark@US.IBM.COM
                Subject: Re: User2 Status


                The list of things fixed in 5.1.2 includes APAR IX88830
Interface in User1
                shows
                User2
                for IP Status field. This corrects the problem where things
that are
                acutally
                User1 show
                up as User2. That does not explain why something you say is
Admin Up is
                being
                set to User1 in the first place. Are you sure it has
ifAdminStatus of 1?
                Netview
                seems
                to treat anything but 1 (including the invalid value 0) as
Admin Down.

                Cordially,

                Leslie A. Clark
                IBM Global Services - Systems Mgmt & Networking


                HI,

                We are running Netview 5.1.1 on AIX 4.2.1. We have Adtran
CSU/DSUs and on
                some of them, when I add them to the map, the IP interface
is green, but
                when I demand poll the unit, Netview changes the IP
interface card to status
                User2 (purple). In Tools>Display Object Info, it shows the
status as
                User2(7), and in Edit>Modify/Describe>Symbol, it shows as
User1Status.

                Can anyone tell me what would cause Netview to put this
status on an IP
                interface? The ifAdminStatus and ifOperStatus are both up.
I'm not sure what
                else to look for.

                Thanks.

When I use the mib browser on these units, I get a status of "up". I would assume it must be interpreting a 1 as up.

I'll put a call in to support and see what they have to say.

Thanks.

-----Original Message-----
From:   Desai, Aditya [mailto:DesaiA@USA.REDCROSS.ORG]
Sent:   Thursday, October 07, 1999 9:58 AM
To:     NV-L@UCSBVM.ucsb.edu
Subject:        Re: User2 Status

Hi Leslie

I have seen similar behaviour on two of our cisco 4500 routers where an link
previously in admin down state, after bringing it up, would stay as user 1
state on Netview.  We are running 5.1.2 on AIX.

Thanks

Ed Desai

American Red Cross

-----Original Message-----
From: Leslie Clark [mailto:NV-L@UCSBVM.ucsb.edu]
Sent: Thursday, October 07, 1999 9:54 AM
To: NV-L@UCSBVM.ucsb.edu; lclark@US.IBM.COM
Subject: Re: User2 Status




The list of things fixed in 5.1.2 includes APAR IX88830 Interface in User1
shows
User2
for IP Status field. This corrects the problem where things that are
acutally
User1 show
up as User2. That does not explain why something you say is Admin Up is
being
set to User1 in the first place. Are you sure it has ifAdminStatus of 1?
Netview
seems
to treat anything but 1 (including the invalid value 0) as Admin Down.

Cordially,

Leslie A. Clark
IBM Global Services - Systems Mgmt & Networking




HI,

We are running Netview 5.1.1 on AIX 4.2.1. We have Adtran CSU/DSUs and on
some of them, when I add them to the map, the IP interface is green, but
when I demand poll the unit, Netview changes the IP interface card to status
User2 (purple). In Tools>Display Object Info, it shows the status as
User2(7), and in Edit>Modify/Describe>Symbol, it shows as User1Status.

Can anyone tell me what would cause Netview to put this status on an IP
interface? The ifAdminStatus and ifOperStatus are both up. I'm not sure what
else to look for.

Thanks.