If you have an NT-Box with HP JetDirect - Software and "Discovery on" in this
software it will poll every IP-Adress in the subnet every 20 seconds with
community "public". If you see this polling-intervall in the
authenticationFailure-traps it's mostly the JetDirect-Software.
Michael Seibold
>>> Leslie Clark <lclark@US.IBM.COM> 21.02.2000 16.10 Uhr >>>
Another common source of bad communities is the HP Jet Direct tools. I
don't
know how that works, but it has been mentioned here before.
Cordially,
Leslie A. Clark
IBM Global Services - Systems Mgmt & Networking
(248) 552-4968 Voicemail, Fax, Pager
---------------------- Forwarded by Leslie Clark/Southfield/IBM on
02/21/2000 10:09 AM ---------------------------
Indy <indy.chakrabarti@ewllc.com>@UCSBVM.UCSB.EDU> on 02/17/2000 11:21:19
AM
Please respond to indy.chakrabarti@ewllc.com
Sent by: Discussion of IBM NetView and POLYCENTER Manager on NetView
<NV-L@UCSBVM.UCSB.EDU>
To: NV-L@UCSBVM.UCSB.EDU
cc:
Subject: Re: Antw: Netview authentication failure on community name
Michael, James (Shanks), thanks for your responses on this. I will
investigate what you guys said.
-----Original Message-----
From: Discussion of IBM NetView and POLYCENTER Manager on NetView
[mailto:NV-L@UCSBVM.ucsb.edu]On Behalf Of Michael Seibold
Sent: Thursday, February 17, 2000 10:06 AM
To: NV-L@UCSBVM.ucsb.edu
Subject: Antw: Netview authentication failure on community name
Have you configured the communities for your loopback-address and your
servers ip address in snmpConf?
Maybe someone else is trying to poll your Server?
If you have cisco routers with authentication traps enabled, try changing
the snmp communities on them to something else than public/private (you
should do it anyway...) on the cisco box and you may see the ip address of
someone else doing an snmp get on your boxes (maybe JetDirect-Server-Tools
or something like that).
Michael Seibold
>>> Indy <indy.chakrabarti@EWLLC.COM> 17.02.2000 16.50 Uhr >>>
I have Netview 5.1.2 on AIX 4.3.2.
I continually get an event that says I have an authentication failure on
the
node on which Netview is installed due to a bad community name. Yet I see
that the node shows as "managed", and that snmpd is running on it, and I
can
do an snmpwalk. The community name is set to public for my entire network,
and I can see the other nodes on the network w/o bad community name
problems. My snmp.conf and snmp.peers file looks okay too. And Netview
seems
to run fine, despite this supposed bad community name. What causes this?
And
how can I turn of this trap so I don't get this error?
Thanks.
**********************************************************************
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they
are addressed. If you have received this email in error please notify
the system manager.
This footnote also confirms that this email message has been swept by
MIMEsweeper for the presence of computer viruses.
www.mimesweeper.com
**********************************************************************
**********************************************************************
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they
are addressed. If you have received this email in error please notify
the system manager.
This footnote also confirms that this email message has been swept by
MIMEsweeper for the presence of computer viruses.
www.mimesweeper.com
**********************************************************************
|