>From memory, I used the standard /opt/CSCOpx/bin/uninstall.sh and it asked
which bits I wanted to uninstall - it's a long time since I did it though....
Cheers,
Jane
Leslie Clark/Southfield/IBM wrote:
> Yes, it did say that. However, the message I got when I tried to install
> was an
> objection to CiscoWorks2000, not just the Integration Utility, and when I
> looked
> under Uninstall, there was no option to remove just the Integration
> Utility. As I
> was pressed for time, I opted to leave the 1.2 on there and import via
> list. Have
> you found a way to remove just that part of it?
>
> Cordially,
>
> Leslie A. Clark
> IBM Global Services - Systems Mgmt & Networking
> Detroit
>
> Jane Curry <jane.curry@skills-1st.co.uk>@tkg.com on 10/28/2000 10:18:20 AM
>
> Please respond to IBM NetView Discussion <nv-l@tkg.com>
>
> Sent by: owner-nv-l@tkg.com
>
> To: NetView mailing list <nv-l@tkg.com>
> cc:
> Subject: [Fwd: Re: [NV-L] CiscoWorks2000 Integration (NT) - a question and
> an answer]
>
> Sorry - comment below should read as..
> "I am pretty certain the CW documentation says you must UNinstall
> one before you install another."
> Cheers, Jane
>
> -------- Original Message --------
> Subject: Re: [NV-L] CiscoWorks2000 Integration (NT) - a question and an
> answer
> Date: Sat, 28 Oct 2000 11:21:30 +0100
> From: Jane Curry <jane.curry@skills-1st.co.uk>
> To: IBM NetView Discussion <nv-l@tkg.com>
> References: <OF155C3BF7.EB57CFE0-ON85256986.00041962@raleigh.ibm.com>
>
> Leslie,
> My understanding from the CW documentation is that you cannot do a
> Remote NMS
> import into RME if your Remote NMS is NT. I have also heard rumours
> that it
> doesn't work trying to import from a Remote Unix NMS to CW on NT, though
> this
> one I know less about.
>
> Re your Integration Utility install, did you uninstall your 1.2
> Integration
> Utility first? I am pretty certain the CW documentation says you must
> install
> one before you install another.
>
> Kind regards,
> Jane
>
> Leslie Clark/Southfield/IBM wrote:
>
> >
> >
> > Then I ran the Integration
> > Utility. OK.
> > Then I tried to run the import from Netview into RME. It would not work.
> > The online
> > help did not sound as if that level of code supported Netview for NT. So
> I
> > downloaded the IU 1.3 , which I have used before, from the well-hidden
> > Cisco
> > website, and found r1.3 refused to install on a box with CiscoWorks2000
> > already on
> > it. The readme clearly states that it is for integration between remote
> > systems.
> > It does, however, install and run fine on the Netview Client. This is
> the
> > level that
> > will be included in newer CD-Ones.
> >
> > Maybe I did it wrong, but it appears to me that not only is combining
> them
> > a bad
> > idea, it will soon be disallowed, if you intend to do any integration.
> > Probably a
> > good idea in most cases, except for small sites who will now need two
> > boxes.
> >
> > Cordially,
> >
> > Leslie A. Clark
> > IBM Global Services - Systems Mgmt & Networking
> > Detroit
> >
> > _________________________________________________________________________
> > NV-L List information and Archives: http://www.tkg.com/nv-l
>
> --
> Tivoli Certified Enterprise Consultant & Instructor
> Skills 1st Limited, 2 Cedar Chase, Taplow, Bucks, SL6 0EU, UK
> Tel: +44 (0)1628 782565
> Copyright (c) 2000 Jane Curry <jane.curry@skills-1st.co.uk>. All rights
> reserved.
> _________________________________________________________________________
> NV-L List information and Archives: http://www.tkg.com/nv-l
>
> _________________________________________________________________________
> NV-L List information and Archives: http://www.tkg.com/nv-l
--
Tivoli Certified Enterprise Consultant & Instructor
Skills 1st Limited, 2 Cedar Chase, Taplow, Bucks, SL6 0EU, UK
Tel: +44 (0)1628 782565
Copyright (c) 2000 Jane Curry <jane.curry@skills-1st.co.uk>. All rights
reserved.
|