I am confused with Don Davis mail:
- in the manuals of Campus Manager (part of CiscoWorks 2000) Cisco System
says that you should have all interfaces that resolves to the same
name (maybe you are referencing another configuration guide of Cisco)
- in our network, we always had different DNS names for all the interfaces
of every router. This is useful if you do a traceroute. We have
about 450 routers, but I have never seen Netview ending up with
multiple routers due to this DNS configuration.
Is it really a Netview requirement to have all the interfaces resolving to
the same name? If there is some good reason, I am ready to change my
DNS configuration.
Thierry
On 22.06.2001 20:15:07 "Davis, Donald" wrote:
>The Interface LABEL will never display anything other that the IP Address
of
>that interface.
>The event log will display the resolved name of the Router (not
interface) if
>it can be resolved.
>If your DNS has different names for each interface on a router (as Cisco
>Systems suggests) then you MUST prevent NetView from
>using DNS for those IP Addresses. You will end up with multiple routers
where
>only one should be drawn.
>DNS overrides NetView's logic as to what interfaces belong to a
particular
>device.
>
>My recommendation is:
>If you have multiple names for the same router in DNS, fix your DNS.
>Get those "unique interface names" out of there or NetView will be
severely
>confused.
>Do not allow NetView to use a DNS for those routers!
>Override it as I previously suggested with /etc/hosts and
/etc/netsvc.conf.
>
>If you do not or cannot (politics) manage your DNS, then this is your
only
>solution.
>Example etc/hosts file:
>
>10.1.1.1 ciscoXYZ # Main IP Address
>10.2.1.1 ciscoXYZ # Serial2/0
>10.3.1.1 ciscoXYZ # Serial2/1
>10.4.1.1 ciscoXYZ # FastEthernet0/0
>10.5.1.1 ciscoXYZ # FastEthernet1/0
>10.6.1.1 ciscoXYZ # FastEthernet3/0
>
>Note that every interface on router ciscoXYZ resolves to the same
hostname !!!
>This is VERY important !!!
>
>James, Feel free to jump in here... :)
>
>Don Davis
>
>
>-----Original Message-----
>From: Stamper, Steve [mailto:Steve_Stamper@foremost.com]
>Sent: Friday, June 22, 2001 12:54 PM
>To: 'IBM NetView Discussion'
>Subject: RE: [NV-L] Object Label
>
>
>Ya but.... What if you have specific interfaces with labels in the DNS?
How
>can you get the interface to pickup the Name and not the IP Address?
>
>
>
>Thanks² - Steve Stamper
>
>-----Original Message-----
>From: Davis, Donald [mailto:donald.davis@firstcitizens.com]
>Sent: Friday, June 22, 2001 11:11 AM
>To: 'IBM NetView Discussion'
>Subject: RE: [NV-L] Object Label
>
>
>Santosh,
>Placing an entry in /etc/hosts will cause NetView to update the selection
name
>when the node is demand (or configuration) polled.
>When you demand poll the node after putting the sysname in /etc/host, you
>should see "New name found ...." in the output window.
>The label of the node will change to this new name. The label of the
interface
>itself will Always be the IP Address.
>I have been told that the label change may not happen immediately,
depending
>how busy NetView is doing other things.
>
>This entry in /etc/hosts will cause the SelectionName and thus the label
to be
>updated with "SuperXyzRouter".
>/etc/hosts
>10.2.3.123 SuperXyzRouter # Comment
>
>Be certain that you have an /etc/netsvc.conf file and it is configured
like
>this:
>
>/etc/netsvc.conf
>hosts=local,bind4
>
>(The number after bind is the version of bind that you are running.)
>If you have not configured /etc/resolv.conf for a nameserver, the
netsvs.conf
>file is not needed.
>This will cause the OS to check /etc/hosts before going to DNS.
>
>Don Davis
>
>
>-----Original Message-----
>From: z_esm_karekars [mailto:z_esm_karekars@bharatpetroleum.com]
>Sent: Friday, June 22, 2001 4:00 AM
>To: 'IBM NetView Discussion'
>Subject: RE: [NV-L] Object Label
>
>
>
>Hi Don,
>
>Can U please be little clear on this, I could enter the Interface IP
addresses
>in /etc/hosts file locally ( Infact I had done it earlier but could not
work
>on that more that time. I tried demand poll after I did the same which
did not
>helped me) How will the interface pickup the Name from hosts file then,
please
>advice.
>
>Regards,
>Santosh
>
>----------
>From: Davis, Donald[SMTP:donald.davis@firstcitizens.com]
>Reply To: IBM NetView Discussion
>Sent: Thursday, June 21, 2001 7:47 PM
>To: 'IBM NetView Discussion'
>Subject: RE: [NV-L] Object Label
>
>Santosh,
>NetView does NOT do this natively (like HP OpenView does). NetView uses
only
>the resolved name.
>The workaround is to write a script that does an SNMPGET for the sysName
and
>writes it to /etc/hosts so that NetView can resolve to that insted of the
DNS
>name. You will need to modify /etc/netsvcs.conf so that local comes
before
>bind.
>
>
>Don Davis
>
>-----Original Message-----
>From: z_esm_karekars [mailto:z_esm_karekars@bharatpetroleum.com]
>Sent: Thursday, June 21, 2001 9:59 AM
>To: 'nv-l@tkg.com'
>Subject: [NV-L] Object Label
>
>
>Hi,
>
>I had Netview 6.0.1 on AIX 4.3.3.
>
>How can the Router Interfaces pick up the System Description
>"RouterName:I/FName" in place of IP address which comes by default.
>
>It's very very urgent.
>
>Regards,
>Santosh
>
>
------------------------------------------------------------------------------
>This electronic mail and any files transmitted with it are confidential
and
>are intended solely for the use of individual or entity to whom they are
>addressed. If you are not the intended recipient or the person
responsible for
>delivering the electronic mail to the intended recipient, be advised that
you
>have received this electronic mail in error and that any use,
dissemination,
>forwarding, printing, or copying of this electronic mail is strictly
>prohibited. If you have received this electronic mail in error, please
>immediately notify the sender by return mail.
>
>
==============================================================================
|