I'm not the expert with regard to using our APIs, but I don't see how you
can do what you want using our code, unless perhaps you can set up name
resolution so that each interface is regarded as a separate host. The way
you want to do things and the way NetView was designed to do them seem to
me to be two entirely different things. As others have already explained,
the NetView model is to let bind with whatever interface it is directed
to. We use whatever works. Once on the box, we let SNMP tell us what the
other interfaces are doing, rather than try to set up separate sessions
over them. xnmsnmpconf lets you set up a preferred interface, but it's
one per host, and if that one's down we'll try another. You really are on
your own here with this design you've cooked up, so far as I can see.
James Shanks
Level 3 Support for Tivoli NetView for UNIX and Windows
Tivoli Software / IBM Software Group
jeff.ctr.vandenbu
ssche@faa.gov
Sent by: To
owner-nv-l@lists. nv-l@lists.us.ibm.com
us.ibm.com cc
Subject
03/31/2005 04:18 Re: [nv-l] Monitoring nodes running
PM ospf
Please respond to
nv-l
James,
What I am mainly looking for is a way to bind Netview to do all it's
outgoing/incoming SNMP querys to a particular IP (interface ) on the
server. I have 3 IP's (interfaces) defined on the server:
server - this IP/interface uses ospf to select which interface to use
server-ethernet0
server-ethernet1
I want Netview to always use the IP associated with server, but Netview
seems to always use the active interface at the time. I know with net-snmp
you can set the address/port you want it to listen on. I actually tried
this, but then netmon failed, stating that SNMP wasn't bound to localhost.
I am having trouble when I fail the active interface, I lose all SNMP
status, instead of swapping to the other interface.
Note we have already had to modify ping, traceroute, etc to bind in this
way. Any way to do this in Netview. Any suggestions would be greatly
appreciated.
Thanks
James Shanks
<jshanks@us.ibm.c
om> To
Sent by: nv-l@lists.us.ibm.com
owner-nv-l@lists. cc
us.ibm.com
Subject
Re: [nv-l] Monitoring nodes running
03/30/2005 12:55 ospf
PM
Please respond to
nv-l@lists.us.ibm
.com
Custom daemons using the OVsnmp APIs? I presume that you've done a lot of
reading in the Programmer's Guide and especially the Programmer's Reference
about using these routines. I can't say I quite follow what you are trying
to do with them, however.
In any case, OVsnmpOpen uses the NetView SNMP database, the one you
maintain with xnmsnmpconf to obtain the peer address for the open. Before
opening the session it does an OVsnmpResolveConfEntry( ) to get the IP
Address or proxy address to use. That means that if there's already an
IP Address in the xnmsnmp cache, he'll use that one. If there isn't one,
he'll try gethostbyname to determine one, and take the first one he gets
back.
So, offhand, my advice would be to trying clearing the xnmsnmpconf cache
before you establish your session. That would force a re-evaluation. You
could even dump it and see what it contains. But if that doesn't do it,
then the issue has to be name resolution.
HTH
James Shanks
Level 3 Support for Tivoli NetView for UNIX and Windows
Tivoli Software / IBM Software Group
jeff.ctr.vandenbu
ssche@faa.gov
Sent by: To
owner-nv-l@lists. nv-l@lists.us.ibm.com
us.ibm.com cc
Subject
03/29/2005 04:07 [nv-l] Monitoring nodes running
PM ospf
Please respond to
nv-l
I have a small network with ~ 12 boxes. Each box consists on 2 Ethernet
ports, and then a 3rd "virtual" interface, with ospf running on each box.
My problem is with several custom polling daemons that status MIB variables
on these various nodes. I have each node defined in the host file on the
Netview box with the virtual IP. The polling daemons use Netview API calls
(OVsnmpOpen) to open an snmp session with each node using the virtual
IP/hostname. The problem occurs during failures. If I fail the active
interface on the remote box, the snmp polling responses timeout, and don't
switch over to the other route to the nodes It seems as if the snmp
session binds to the active interface, rather than the virtual IP that is
defined.
Also, if I shutdown the active interface on the Netview box, I lose all
statuses from all nodes. I am not sure if this is a Netview configuration,
a Netview API, or an snmp issue. Any suggestions??
Is there a way to setup Netview to status (via SNMP) multiple IP addresses
for the same node.
Can a daemon/lrf be set up to respawn? I could then have the session
timeout, then respawn.
Thanks,
Jeff VanDenbussche
JSA/ATO-E
HNL Support
(609) 485-4200
|