RE: [NV-L] Reg Discovery

["Santhanakrishnan Janakiraman (IT Services), Chennai" <santhanakrishnanjn@hcl.in>]

Hi,

 

When i do rnetstat -lx , iam getting an error . But I can able to do rnetstat -ix 10.x.x.x  for the same IP. Please advice me on this.

 

 

# rnetstat -lx 10.x.x.x
Local Address               Remote Address              (state)
ERROR getting table from 10.x.x.x: The variable does not exist or is read only.

Thanks & Regards

SanthanaKrishnan.J

Office: 044-28221129 Ext-2206

Mobile: +91- 9840943639

 

 

---

From: nv-l-bounces@lists.ca.ibm.com [mailto:nv-l-bounces@lists.ca.ibm.com] On Behalf Of James Shanks
Sent: Wednesday, June 06, 2007 6:58 PM
To: Tivoli NetView Discussions
Subject: RE: [NV-L] Reg Discovery

I have no idea. That's a local issue. but perhaps you can get netmon to tell you.

Try putting that IP address in the seed file as the first entry. The turn on the full netmon trace
netmon -M -1
Then tell netmon to reload the seed file
netmon -y
and watch what happens in the netmon.trace file for that IP address.

Turn off the trace with
netmon -M 0

James Shanks
Level 3 Support for Tivoli NetView for UNIX and Windows
Network Availability Management
Network Management - Development
Tivoli Software, IBM Corp
"Santhanakrishnan Janakiraman (IT Services), Chennai" <santhanakrishnanjn@hcl.in>

"Santhanakrishnan Janakiraman (IT Services), Chennai" <santhanakrishnanjn@hcl.in>
Sent by: nv-l-bounces@lists.ca.ibm.com

06/06/2007 05:58 AM

Please respond to
Tivoli NetView Discussions <nv-l@lists.ca.ibm.com>

To	"Tivoli NetView Discussions" <nv-l@lists.ca.ibm.com>
cc
Subject	RE: [NV-L] Reg Discovery

Hi,

Iam trying to discover a IP address but i cant 
why?

Thanks & Regards

SanthanaKrishnan.J

Office: 044-28221129 Ext-2206

Mobile: +91- 9840943639

---

From: 
nv-l-bounces@lists.ca.ibm.com [mailto:nv-l-bounces@lists.ca.ibm.com] 
On Behalf Of Leslie 
Clark
Sent: Tuesday, 
June 05, 2007 11:52 PM
To: Tivoli NetView Discussions
Subject: RE: [NV-L] Reg 
Discovery


In addition to what Bill 
said..... 

If it were a router, Netview would have 
used the connector symbol by default. What you see indicates that Netview has 
not been able to talk SNMP to this device to determine that it has multiple IP 
addresses, so it made it a plain node. 

If, on the 
other hand, what you have discovered is a layer2 switch that only has one IP 
address, then Netview will not promote it to the top level of the map or give it 
a connector symbol even if it is SNMP. To tell the difference, look at the 
object information: Tools...Display Object Information. See if it is really SNMP 
supprted, and if so, what is its SNMP sysObjectID. 

Cordially,

Leslie A. Clark
IT Services Specialist, Network 
Mgmt
Information Technology Services Americas
IBM Global Services
(248) 
552-4968 Voicemail, Fax, Pager

"Evans, Bill" <Bill.Evans@hq.doe.gov>
Sent by: nv-l-bounces@lists.ca.ibm.com

06/05/2007 01:17 PM

Please respond to
Tivoli NetView Discussions <nv-l@lists.ca.ibm.com>

To	"Tivoli NetView Discussions" <nv-l@lists.ca.ibm.com>
cc
Subject	RE: [NV-L] Reg Discovery

The default symbol selected when the object is 
discovered depends on the
relationships of the Object Identifier (OID) found 
in the
/usr/OV/conf/oid_to_xxxx files and various files in the 
/usr/OV/bitmaps,
.../symbols and .../fields files.  It's covered in the 
books. 

It's easier to select your node symbol and use the 
RightMouseClick and
Edit->Change-Symbol-Type service on the classic 
console.  It's very
similar to how you create an icon manually. 
 

Bill Evans

-----Original Message-----
From: 
nv-l-bounces@lists.ca.ibm.com
[mailto:nv-l-bounces@lists.ca.ibm.com] 
On Behalf Of Santhanakrishnan
Janakiraman (IT Services), Chennai
Sent: 
Tuesday, June 05, 2007 12:08 PM
To: Tivoli NetView Discussions
Subject: 
[NV-L] Reg Discovery




Hi,

I am trying to discover a 
router, i have mentioned the IP address of
that router in netmon.seed file, 
netview can able to discover that
object but the object iam getting doesnt 
represent the router (
connector ) symbol, it shows a node symbol, what i 
have to do now. That
comes within segment. Please advice me on this. Iam 
using Netview
7.1.4.4 in AIX. 

Thanks & 
Regards
SanthanaKrishnan.J
Office: 044-28221129 Ext-2206
Mobile: +91- 
9840943639
<<Picture (Metafile)>> 




DISCLAIMER:
------------------------------------------------------------------------
-----------------------------------------------

The 
contents of this e-mail and any attachment(s) are confidential and
intended 
for the named recipient(s) only.
It shall not attach any liability on the 
originator or HCL or its
affiliates. Any views or opinions presented in 
this email are solely those of the author and may not necessarily
reflect 
the opinions of HCL or its affiliates.
Any form of reproduction, 
dissemination, copying, disclosure,
modification, distribution and / or 
publication of 
this message without the prior written consent of the author 
of this
e-mail is strictly prohibited. If you have
received this email in 
error please delete it and notify the sender
immediately. Before opening any 
mail and 
attachments please check them for viruses and 
defect.

------------------------------------------------------------------------
-----------------------------------------------


_______________________________________________
NV-L 
mailing 
list
NV-L@lists.ca.ibm.com
Unsubscribe:NV-L-leave@lists.ca.ibm.com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser 
access limited to internal IBM'ers only)
_______________________________________________
NV-L 
mailing 
list
NV-L@lists.ca.ibm.com
Unsubscribe:NV-L-leave@lists.ca.ibm.com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser 
access limited to internal IBM'ers only)

_______________________________________________
NV-L mailing list
NV-L@lists.ca.ibm.com
Unsubscribe:NV-L-leave@lists.ca.ibm.com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to 
internal IBM'ers only)