i would think a successful "discovery" requires a response to a ping as a
minimum requirement, so your suspicion would be right
Gareth Holl
Software Engineer
gholl@tivoli.com
Tivoli Systems / IBM Corporation
Research Triangle Park, North Carolina. 1-800-TIVOLI-8
-----------------------------------------------------------------------------------------------------------
No matter what happens, somebody will find a way to take it too seriously
"Cowan, Chris" <Chris.Cowan@2ndWaveinc.com>@tkg.com on 06/01/2001 11:29:48
AM
Please respond to IBM NetView Discussion <nv-l@tkg.com>
Sent by: owner-nv-l@tkg.com
To: "'IBM NetView Discussion'" <nv-l@tkg.com>
cc:
Subject: Unable to discover nodes using SNMP status Was: [NV-L] OIDs Seedf
iles and SNMP status polling
Well the reason that I want to use SNMP status rather than pings is that
ICMP echos are blocked at a private VLAN boundary, but SNMP isn't.
Which brings me to my question. I attempted to SNMP status query 2 Nokia
Crypto Clusters (actually it's an HA config with 2 boxes and a 3rd shared
address). I can snmpwalk the two systems, but as stated earlier ICMP
echos are blocked. For some reason, the two boxes will not discover.
I'm not sure if it is because pings are blocked, or that there is a 3rd
virtual address. I am about to try tracing netmon and all that, but
figured I would look out here and just see if anyone has tips or ideas.
Thanks in advance.
-----Original Message-----
From: James_Shanks@TIVOLI.COM [mailto:James_Shanks@TIVOLI.COM]
Sent: Tuesday, March 20, 2001 8:20 AM
To: IBM NetView Discussion
Subject: Re: [NV-L] OIDs Seedfiles and SNMP status polling
Just a question on why you would want to do this.
Since the overhead involved to get status via SNMP rather than by ping is
so much greater, why would you want to make that the default? Getting
status via SNMP is a very new feature in NetView and it should be used
sparingly, which probably accounts more than anything else for why you
cannot simply set things up as you suggest. I think product management
would want to see a full-blown performance analysis before they'd let such
a feature out the door. But that is just my opinion here.
If you think this should be a feature, then my suggestion is that you call
Support and open an enhancement request.
James Shanks
Team Leader, Level 3 Support
Tivoli NetView for UNIX and NT
danny@UK.IBM.COM@tkg.com on 03/20/2001 08:09:26 AM
Please respond to IBM NetView Discussion <nv-l@tkg.com>
Sent by: owner-nv-l@tkg.com
To: nv-l@tkg.com
cc:
Subject: [NV-L] OIDs Seedfiles and SNMP status polling
Hi All
I am attempting to have my cake and eat it, so please don't flame me for
presenting an unreasonable request:
I have a seedfile that contains IP addresses and IP address. What I would
like to do is status poll most of the devices using SNMP. However, if I
understand correctly, one must first discover the object and then add the
"$" before the IP address or hostname in the seedfile.
So I had an idea: how about using OIDs - maybe I can put the following line
in my seedfile and run "netmon -y" (it's the OID of a printer)
$@oid 1.3.6.1.4.1.2001.1.2.683.6
No such luck.
Therefore, the only solution that I can think of is to work through the
database to see which objects have been discovered and support SNMP and
have the appropriate OID and update the seedfile accordingly (not
forgetting the netmon -y afterwards).
I'm sure that someone out there has had to deal with the same issue.
Wouldn't it be great if there was a flag you could set somewhere that says
"If the object supports SNMP, use SNMP to status poll it"?
Any ideas anyone?
Cheers.
Danny
Danny Williams
Tivoli & AIX Specialist
IBM Global Services - Integrated Technology Services
mailto:danny@uk.ibm.com
Tel: 665520 (01926-465520) -- MOBX: 275520 (07967-275520)
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
|