From
what I read it became standard 2/2002?
>>> "Key, Chris"
<Chris.Key@hq.doe.gov> 05/01/02 12:24PM >>>
Correct me if I am wrong, but isn't SNMP "v3" still an
un-ratified standard? Any implementations would be vendor proprietary
right?
I would think NetView support would come after a final
standard.
-----Original Message-----
From: James
Shanks [mailto:jshanks@us.ibm.com]
Sent: Wednesday, May 01, 2002 1:18 PM
To:
nv-l@lists.tivoli.com
Subject: RE: [nv-l] SNMPv3
There is no SNMP V3 support announced for NetView at this time,
so you
cannot expect anything from NetView in the short
run.
Are you saying that if you enable this RAT feature, then your
Cisco
routers will only support SNMP V3 requests?
That they will not honor an
SNMP V1 request for MIB-II
data, which is all that NetView needs for a
config check
or discovery? That seems awfully restrictive. One of the
features of SNMP V3 is supposed to be that you can
designate which parts
of the MIB tree are secure and
which are not.
Perhaps you should arrange to try this on one router and see
what happens.
James Shanks
Level 3 Support for
Tivoli NetView for UNIX and NT
Tivoli Software / IBM
Software Group
"CATALINA MARTINEZ"
<CATALINA.MARTINEZ@tlc.state.tx.us>
05/01/2002
11:31 AM
To:
<nv-l@lists.tivoli.com>
cc:
Subject: RE: [nv-l] SNMPv3
Yes,
Router Audit Tool (rat) is a tool to audit Cisco IOS configurations and
display the results in an HTML format. Since
SNMPv3 provides secure
access to devices by a
combination of authenticating and encrypting
packets
over the network, its recommended when using RAT. We are still in
the process of researching this. But from what we
understand we must
configure snmpv3 on the routers who
will use RAT..
So if Netview does not support snmpv3, we
wont be able to monitor them.
Before I tell management
NO on Netview, is there anything in the works for
v3?
Catalina
>>> "Treptow, Craig"
<Treptow.Craig@principal.com> 05/01/02 09:59AM >>>
It's gotta be the "Router Audit Tool" released by SANS and
found on http://www.cisecurity.org/
-----Original Message-----
From: James
Shanks [mailto:jshanks@us.ibm.com]
Sent: Wednesday, May 01, 2002 9:00 AM
To:
nv-l@lists.tivoli.com
Subject: Re: [nv-l] SNMPv3
No, NetView does not support SNMP V3 at this time.
Can you explain what "RAT" is and why it would require NetView
to use SNMP
V3 in order for you to implement it?
James Shanks
Level 3 Support for
Tivoli NetView for UNIX and NT
Tivoli Software / IBM
Software Group
"CATALINA MARTINEZ"
<CATALINA.MARTINEZ@tlc.state.tx.us>
05/01/2002
09:41 AM
To: <nv-l@lists.tivoli.com>, Leslie
Clark/Southfield/IBM@IBMUS
cc:
Subject: [nv-l] SNMPv3
Hello,
Does Netview support snmpv3? we want to configure our routers to
be able
to use "RAT" but in it only works with
SNMPv3..
Thanks,
Catalina
Netview 602
AIX 4337
---------------------------------------------------------------------
To unsubscribe, e-mail:
nv-l-unsubscribe@lists.tivoli.com
For additional
commands, e-mail: nv-l-help@lists.tivoli.com
*NOTE*
This is not an Offical Tivoli
Support forum. If you need immediate
assistance from
Tivoli please call the IBM Tivoli Software Group
help
line at 1-800-TIVOLI8(848-6548)
---------------------------------------------------------------------
To unsubscribe, e-mail:
nv-l-unsubscribe@lists.tivoli.com
For additional
commands, e-mail: nv-l-help@lists.tivoli.com
*NOTE*
This is not an Offical Tivoli
Support forum. If you need immediate
assistance from
Tivoli please call the IBM Tivoli Software Group
help
line at 1-800-TIVOLI8(848-6548)
---------------------------------------------------------------------
To unsubscribe, e-mail:
nv-l-unsubscribe@lists.tivoli.com
For additional
commands, e-mail: nv-l-help@lists.tivoli.com
*NOTE*
This is not an Offical Tivoli
Support forum. If you need immediate
assistance from
Tivoli please call the IBM Tivoli Software Group
help
line at 1-800-TIVOLI8(848-6548)
|