James,
I will definitely call Support to get a 6.0.3
Thanks for your information.
Eli
--- James Shanks <jshanks@us.ibm.com> wrote:
> I would call Support and get the latest tecad binary
> from them there were
> problems with the EIF library build in 6.0, 6.0.1,
> and 6.0.2, which are
> not corrected until 6.0.3. The APAR is PJ28060. I
> would not even attempt
> to proceed without this fix. And I would make plans
> to get 6.0.3 itself.
>
> James Shanks
> Level 3 Support for Tivoli NetView for UNIX and NT
> Tivoli Software / IBM Software Group
>
>
>
>
>
>
> Eliza Chi <elizachi728@yahoo.com>
> Sent by: owner-nv-l@tkg.com
> 12/21/2001 03:00 PM
> Please respond to IBM NetView Discussion
>
>
> To: nv-l@tkg.com
> cc:
> Subject: [NV-L] tecad_nv6k starts
> with EIF error
>
>
>
> Hi,
>
> Can someone help me to figure out the problem?
> Thanks
> in advance.
>
> ---------------------------
> My environment:
>
> Spoke TMR server 3.6.2, (NT)/Netview Server 6.0.1
> (NT)
> TEC Netview adapter 3.6 are on one machine which is
> my
> Netview server.
>
> Hub TMR 3.6.2 (NT)
>
> TEC 3.6.2 (NT) in hub TMR.
> -----------------------------
> I have been tring to send netview events to the TEC
> server in the hub TMR, but the behavior attribute of
> "ovstatus tecad_nv6k" always shows:
> started... then not running.
> I looked at log file from the tecio module
> configured
> in tecad_nv6k.err and saw the following error
> message.
>
>
> Fri Dec 21 14:14:03 2001 FATAL: TECIO , err 01,
> ibtecad/tec_io.c line 0516: C
> annot create EIF handle. Please check the .conf
> file.
>
> I know this message is related to the ServerLocation
> in tecad_nv6k.conf, but I configured the
> ServerLocation:
>
> ServerLocation=@EventServer#hub_tmr-region
>
> I even tried @EventServer, Server IP, Server
> hostname
> but to the same error message. (I knew these did not
> make sense to me, but I just tried)
>
> I have done:
>
> 1. wlsconn on both hub tmr and spoke tmr/Netview
> I saw two way interconnected tmrs
>
> 2. odadmin odlist on both tmr and they are fine
>
> 3. wupdate -r EventServer hub_tmr-region on the
> spoke tmr/netview server,
>
> 4. wlookup -ar EventServer
> shows the EventServer with the hub tmr region oid
>
> 5. wpostemsg OV_IF_Down events works fine from a
> CLI,
> tec processed the OV_IF_Down messages, the events
> were
> displayed on TEC Console
>
> but I still can't bring up tecad_nv6k. Did I miss
> anything?
>
> I installed TEC on the spoke tmr/Netview server
> once,
> but I did wdel /Library/EventServer and wregister -u
> -r
> EventServer EventServer, wchkdb, so the spoke
> tmr/netview now only sees the tec server in hub tmr
> and wpostemsg works fine.
>
> Did anyone get this error before. Does any one know
> what ibtecad/tec_io.c line 0516 is trying to check?
>
>
>
> Eli
>
>
>
>
> __________________________________________________
> Do You Yahoo!?
> Check out Yahoo! Shopping and Yahoo! Auctions for
> all of
> your unique holiday gifts! Buy at
> http://shopping.yahoo.com
> or bid at http://auctions.yahoo.com
>
_________________________________________________________________________
> NV-L List information and Archives:
> http://www.tkg.com/nv-l
>
>
>
__________________________________________________
Do You Yahoo!?
|