Bernard,
James Shanks suggested to upgrade to NV6.0.3 should
fix this problem. Before I receive the CD from
Tivoli, I would like to take your advice. This
afternoon, I switched TME tecad_nv6k to a NON TME
tecad_nv6k. tecad_nv6k is running but I got a
different error:
MAJOR: TECIO , err 01, ibtecad/tec_io.c line 0287: E
vent could not be sent properly
What Netview version are you running? NT or UNIX? Have
you seen this error before?
Thanks for your advise.
Eli
--- Bernard Disselborg <bdisselb@triple-p.nl> wrote:
> Eliza,
>
> I don't have a real 'answer', but this is my
> experience:
> I've once tried to use the tme version of the
> adapter, as you are trying to
> do, I did not succeed.
> Using the non-tme version never causes me any
> problems, so I always use
> this setup.
>
> HTH,
>
> Bernard
>
> At 12:00 21-12-2001 -0800, you wrote:
> >Hi,
> >
> >Can someone help me to figure out the problem?
> Thanks
> >in advance.
> >
> >---------------------------
> >My environment:
> >
> >Spoke TMR server 3.6.2, (NT)/Netview Server 6.0.1
> (NT)
> >TEC Netview adapter 3.6 are on one machine which is
> my
> >Netview server.
> >
> >Hub TMR 3.6.2 (NT)
> >
> >TEC 3.6.2 (NT) in hub TMR.
> >-----------------------------
> >I have been tring to send netview events to the TEC
> >server in the hub TMR, but the behavior attribute
> of
> >"ovstatus tecad_nv6k" always shows:
> >started... then not running.
> >I looked at log file from the tecio module
> configured
> >in tecad_nv6k.err and saw the following error
> message.
> >
> >
> >Fri Dec 21 14:14:03 2001 FATAL: TECIO , err 01,
> >ibtecad/tec_io.c line 0516: C
> >annot create EIF handle. Please check the .conf
> file.
> >
> >I know this message is related to the
> ServerLocation
> >in tecad_nv6k.conf, but I configured the
> >ServerLocation:
> >
> > ServerLocation=@EventServer#hub_tmr-region
> >
> >I even tried @EventServer, Server IP, Server
> hostname
> >but to the same error message. (I knew these did
> not
> >make sense to me, but I just tried)
> >
> >I have done:
> >
> >1. wlsconn on both hub tmr and spoke tmr/Netview
> >I saw two way interconnected tmrs
> >
> >2. odadmin odlist on both tmr and they are fine
> >
> >3. wupdate -r EventServer hub_tmr-region on the
> >spoke tmr/netview server,
> >
> >4. wlookup -ar EventServer
> >shows the EventServer with the hub tmr region oid
> >
> >5. wpostemsg OV_IF_Down events works fine from a
> CLI,
> >tec processed the OV_IF_Down messages, the events
> were
> >displayed on TEC Console
> >
> >but I still can't bring up tecad_nv6k. Did I miss
> >anything?
> >
> >I installed TEC on the spoke tmr/Netview server
> once,
> >but I did wdel /Library/EventServer and wregister
> -u
> >-r
> >EventServer EventServer, wchkdb, so the spoke
> >tmr/netview now only sees the tec server in hub tmr
> >and wpostemsg works fine.
> >
> >Did anyone get this error before. Does any one
> know
> >what ibtecad/tec_io.c line 0516 is trying to check?
> >
> >
> >
> >Eli
> >
> >
> >
> >
> >__________________________________________________
> >Do You Yahoo!?
> >Check out Yahoo! Shopping and Yahoo! Auctions for
> all of
> >your unique holiday gifts! Buy at
> http://shopping.yahoo.com
> >or bid at http://auctions.yahoo.com
>
>_________________________________________________________________________
> >NV-L List information and Archives:
> http://www.tkg.com/nv-l
>
>
_________________________________________________________________________
> NV-L List information and Archives:
http://www.tkg.com/nv-l
__________________________________________________
Do You Yahoo!?
|