Hi Frank, All,
I wanted to ask how you 'turn on' and 'turn off' the holding area?
Also - I'm unable to click/drag/move objects on my map to containers I want
them to be in. . .does anyone know if there's a configuration change I need to
invoke that allows me to do that?
Thanks to all in advance. . .
Dan
-----Original Message-----
From: DePhillips, Frank [mailto:fdephillips@McLeodUSA.com]
Sent: Fri 3/28/2003 12:43 PM
To: 'James Shanks'; nv-l@lists.tivoli.com
Cc:
Subject: RE: [nv-l] problem with node not showing up on map
James,
I have the holding area turned on so all new routers get placed
in the holding area before I put them on the map. I added four routers last
week and this one did not show up. I did a locate and the router was not found
by name or ip address. I just ran the ovobjprint command and looked for the ip
address and name in the output and it was not found. I have one map that is
running production monitoring and I'm currently running a new map to clean up
placement of nodes.
I just tried to create the router by adding a new object and it
comes back with the object selection name already exists and is a different
type.
Any other way I can find this object and delete it?
Thanks
Frank
-----Original Message-----
From: James Shanks [mailto:jshanks@us.ibm.com]
Sent: Friday, March 28, 2003 8:48 AM
To: nv-l@lists.tivoli.com
Subject: Re: [nv-l] problem with node not showing up on map
How do you know it's not on the map? Did you try Locate?
If Locate fails to find it, then print the database with ovobjprint,
"ovobjprint > ovobjprint.out", and examine the output. If you find
the
object it should have two fields, OVW Maps Exit and OVW Maps Managed
and
they should both have at least a value of 1. Do they? At the bottom
of
the record will be entries for the IP Symbol List for each of your
maps.
You should have at least one map, usually called "default", so you
should
see at least one entry which says "default IP Symbol List" followed by
some number. Is that there? Do you have more than one map?
James Shanks
Level 3 Support for Tivoli NetView for UNIX and NT
Tivoli Software / IBM Software Group
"DePhillips, Frank" <fdephillips@McLeodUSA.com>
03/28/2003 09:38 AM
To: nv-l@lists.tivoli.com
cc:
Subject: [nv-l] problem with node not showing up on map
I have added a node to the seedfile and run netmon -y and it
does not show
up on the map. If I try to create the node manually it will say node
already exsists. How can I find this node or delete and recreate?
Thanks
Frank
NOTICE: This electronic mail transmission may contain confidential
information and is intended only for the person(s) named. Any use,
copying or disclosure by any other person is strictly prohibited. If
you
have received this transmission in error, please notify the sender via
e-mail.
---------------------------------------------------------------------
To unsubscribe, e-mail: nv-l-unsubscribe@lists.tivoli.com
For additional commands, e-mail: nv-l-help@lists.tivoli.com
*NOTE*
This is not an Offical Tivoli Support forum. If you need immediate
assistance from Tivoli please call the IBM Tivoli Software Group
help line at 1-800-TIVOLI8(848-6548)
NOTICE: This electronic mail transmission may contain confidential
information and is intended only for the person(s) named. Any use, copying or
disclosure by any other person is strictly prohibited. If you have received
this transmission in error, please notify the sender via e-mail.
|